+39 331 584 7291 [email protected] Mon-Fri 8:00-17:30 (CET)
I Need Some Help On Visio Diagramming

I Need Some Help On Visio Diagramming

Browse technical resources about specialty optical cables, hybrid cables, waterproof patch cords, MPO/MTP, AWG WDM, 800G transceivers, testers, outdoor power cabinets, DCI, smart grid and industrial o...

  • Do all servers need to be connected to an FC switch

    Do all servers need to be connected to an FC switch

    An FC switch eliminates the need for every server to have a direct connection to every storage array and thus reduces complexity. Fibre Channel (FC), designed for storage area networks (SANs), is a high-speed network technology used to connect computer data storage to servers, providing point-to-point, switched and loop interfaces to deliver in-order and lossless raw block data. This configuration provides connections to each of the counterpart SANS. When configured as a Fibre Channel over Ethernet (FCoE)-FC gateway, the QFX3500 switch supports the transport of native FC traffic between FC switches and the gateway's native FC interfaces. The different types of FC architecture which can be designed are Fibre channel switched fabric (FC-SW).


  • Do multimode optical modules need spectral measurement

    Do multimode optical modules need spectral measurement

    Spectral testing is another common method for testing multimode optical modules. During the testing process, it is necessary to connect the test light source to the input end of the optical module, and then connect the output end to the spectrometer. Abstract: A standard multimode optical fiber can be used as a general purpose spectrometer after calibrating the wavelength dependent speckle patterns produced by interference between the guided modes of the fiber. A transmission matrix was used to store the calibration data and a robust algorithm. Multi-mode optical fiber is a type of optical fiber mostly used for communication over short distances, such as within a building or on a campus. No part of this book may be reproduced or utilized in any form or means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system, without pe n optical fiber to a distant receiver.

    [PDF Version]
  • Do high-rise cable trays not need to be used for cable laying

    Do high-rise cable trays not need to be used for cable laying

    If you need maximum cable support to minimize bends (fiber), cable tray is the best solution. Cable trays are a support system for electrical cables, power, signal, and communication and optical fiber cables. NEC section 300-8 does not permit any tube, pipe, or equal for water, air gas, drainage, steam, or any service other than electrical in raceways or cable trays containing. NEC Article 392 explains cable trays, their components, appropriate wiring methods for cable trays, and instances where they are and are not permitted for use. It also focuses on construction and installation practices for cable trays. Here is the summary of the main points found in NEC Article. The primary rulebook used in the safe use of cable trays is NEC Article 392. 305(a)(3), or comparable standards promulgated by States. Ladder rack (also known as “ladder trays” or “cable ladders”) are one of the most common types of cable runway.

    [PDF Version]
  • Does the lighting distribution box need to be sealed off

    Does the lighting distribution box need to be sealed off

    Every box must be closed with a securely fastened cover, faceplate, or fixture canopy. For the lighting there are seal off's on each side of a junction box that splits off to feed the (3) seperate switch locations. Most failures come from water intrusion, not the box itself. Outdoor lighting junction boxes must do more. Electric equipment shall be free from recognized hazards that are likely to cause death or serious physical harm to employees. Safety of equipment shall be determined using the following considerations: Suitability for installation and use in conformity with the provisions of this subpart; Note to. Learn how to seal electrical enclosures effectively to protect equipment from moisture, dust, and harsh environments. Step-by-step guide and expert tips. Electrical and communication conditioned and unconditioned spaces.


  • Do I need to buy a panel for fiber optic cables

    Do I need to buy a panel for fiber optic cables

    Choosing the right fiber optic patch panel is one of the most important decisions you'll make when building or upgrading a fiber network. A well-designed patch panel doesn't just organize cables — it protects your connections, improves signal performance, and makes. With the growth of the fiber industry, a wide array of fiber optic patch panels have been developed to fit the many needs of these varying environments. If you already know what your project requires, check out our complete Fiber Patch Panel selection. A fiber optic patch panel or wall mount enclosure not only enables electricians and network engineers to connect and manipulate cables, it also offers a safe working. A fiber patch panel is essential in assisting with this issue as it provides a systematic method of terminating, connecting and organizing fiber optic cables. They enable efficient signal routing, maintenance, and troubleshooting within telecommunications and data center environments. The panel houses adapters or.

    [PDF Version]

Need Product Pricing?

Contact us for competitive quotes on any of our fiber optic and telecom products

Get a Quote